Search Results

The structure-borne vibration paths within the power train and the vehicle are complicated and have been studied for years. This complication is a result of multiple attachment locations, and directions that exhibit flexural resonance in both the source-side and response-side of the path. To aid understanding in discussion of the dynamic properties of an individual vibration path, simplified mechanical mobility models are employed. These models are typically more simplified by assigning classical elemental properties to the individual components represented in the model. An analysis was performed to understand the significance of more “real-like” component mobility properties on system response and isolation, consistent with the conversational mathematical interpretation. Components within the vibration path are modeled as multiple lumped-parameter elements.

This paper describes a technique to approximately compute the dynamic forces and moments acting on the crankshaft-flywheel joint as well as the crank nose using measurement data. The same technique can also be used on data generated by dynamic simulations. The method is based on rigid body dynamics where the measured accelerations and velocities are substituted into the equations of motion to compute the dynamic forces and moments. However, using the measured (or simulated data) in the equations of motion is not straightforward and requires special measurement techniques and data analysis procedures. This paper describes the special measurement techniques and apparatus, as well as the data analysis techniques necessary for proper computation of the dynamic forces and moments.

This paper describes the development of a generic test cell software designed to overcome many vehicle-component testing difficulties by introducing modern, real-time control and simulation capabilities directly to laboratory test environments. Successfully demonstrated in a transmission test cell system, this software eliminated the need for internal combustion engines (ICE) and test-track vehicles. It incorporated the control of an advanced AC induction motor that electrically simulated the ICE and a DC dynamometer that electrically replicated vehicle loads. Engine behaviors controlled by the software included not only the average crankshaft torque production but also engine inertia and firing pulses, particularly during shifts. Vehicle loads included rolling resistance, aerodynamic drag, grade, and more importantly, vehicle inertia corresponding to sport utility, light truck, or passenger cars.

The results of an experimental investigation of the flow over a pickup truck are presented. The main objectives of the study are to gain a better understanding of the flow structure in near wake region, and to obtain a detailed quantitative data set for validation of numerical simulations of this flow. Experiments were conducted at moderate Reynolds numbers (∼3×105) in the open return tunnel at the University of Michigan. Measured quantities include: the mean pressure on the symmetry plane, unsteady pressure in the bed, and Particle Image Velocimetry (PIV) measurements of the flow in the near wake. The unsteady pressure results show that pressure fluctuations in the forward section of the bed are small and increase significantly at the edge of the tailgate. Pressure fluctuation spectra at the edge of the tailgate show a spectral peak at a Strouhal number of 0.07 and large energy content at very low frequency.

An automatic optimization process for the aerodynamic design of automotive vehicle shapes is presented. The Computational Fluid Dynamics (CFD) mesh generation and the analysis software packages are coupled for transfer of data and information between the two packages. This communication enables an automated process in which designs are created and analyzed for the aerodynamic drag. New designs are created by morphing the CFD model for the baseline design. The automated process is applied to perform a parametric study on a generic automobile sedan shape. The results show that the process can be used for aerodynamic optimization of any automotive vehicle shape. The turnaround for the automated process is at least an order of magnitude less than the conventional analysis process.

Effects of the pressure gradient in the wind tunnel test section on vehicle aerodynamic drag were investigated using computational fluid dynamics (CFD). The numerical study was used to obtain the aerodynamic drag of several vehicles in two virtual wind tunnels, one with a zero pressure gradient and another with a nonzero (but small) pressure gradient. A comparison of the vehicle aerodynamic drags in these two virtual wind tunnels, and investigation of the physical mechanisms causing these differences, have led to two correction formulas. These formulas can be used to correct for the pressure gradient effect on vehicle aerodynamic drag measurement in a wind tunnel that has a nonzero pressure gradient. In the first formula, the correction is given explicitly in terms of known variables. The correction is 80% accurate for passenger car, sports car, sports utility vehicle (SUV), and is 70% accurate for pickup truck.

As automotive exhaust emission levels reduce, there is a need for increased sensitivity of the NOx measurement. This paper documents work performed to increase the sensitivity of the existing Rosemount NGA 2000 CLD Analyzer. The effects of sample flow rate, ozone flow rate and ozone supply gas were explored. Limit of Detection (LOD) and Converter Efficiency were evaluated. The goal of this optimization has been to provide a cost effective and expeditious method to improve the low level NOx measurement. Changing the ozone generator supply gas from air to oxygen and increasing the sample and ozone flow rates resulted in a LOD improvement from 17 ppb to 8 ppb.

The Corrosion Task Force of the Automotive/Steel Partnership has developed the SAE J2334 cyclic laboratory test for evaluating the cosmetic corrosion resistance of auto body steel sheet. [Ref. 1] Since the publishing of this test in 1997, further work has improved the precision of J2334. In this paper, the results of this work along with the revisions to the J2334 test will be discussed.

The introduction of the continuously variable transmission (CVT) by General Motors required the introduction of a test to evaluate fluid for the ECOTEC VTi transmission. With assistance from Van Doorne's Transmissie (VDT), the belt and sheave supplier for the transmission, a rig was constructed to test fluids in a transmission-like environment without the variability of in-vehicle testing. The test schedule includes testing for fluid friction coefficient, shear stability, and wear rating and is currently subject to further work aimed at confirming repeatability and discrimination. Once confirmed, the new procedure will become part of the DEX-CVT® specification for the new service fluids for the VT20/25E transmissions.

Sport Utility Vehicles (SUV) and light duty trucks have gained in popularity for the last several years and the demand for more car-like behavior has increased, accordingly. Two areas for potential improvement are vehicle stability and maneuverability while parking. 4WS (4 wheel steering system) is known as an effective solution to stability and low speed maneuverability. In this paper, we identify a new systematic design method of two degree of freedom vehicle state feedback control algorithm that can improve vehicle stability, and show its control effects for a SUV with trailer towing. Low speed maneuvering is improved when the rear tires are steered in negative phase relative to the front tires. However with a large rear steer angle at low speed, the vehicle's rear overhang tracks a wider swing-out path than a 2WS vehicle. For this concern, we propose a new swing-out reduction control algorithm.

The close-fitting cockpit of the modern Indy car single seat race car has the potential to provide a high level of head and neck impact protection in rear and side impacts. Crash investigation has shown that a wide variety of materials have been used as the padding for these cockpits and, as a result, produced varying outcomes in crashes. Additionally, these pads have not always been positioned for optimal performance. The purpose of this study was to investigate the head impact performance of a variety of energy-absorbing padding materials under impact conditions typical of Indy car rear impacts and to identify superior materials and methods of improving their performance as race car head pads. An extensive series of tests with the helmeted Hybrid III test dummy head and neck on an impact mini-sled was conducted to explore head padding concepts.

A roll down methodology has been developed to predict the driver's seat track fore-aft acceleration response using measured half shaft torque time histories and an analytically predicted vehicle sensitivity function suitable for transverse front wheel drive powertrains. The predicted vehicle sensitivity function (a frequency response function) relates the transmission torque applied to the drive axles to the seat track fore-aft acceleration. An experimental procedure was developed to measure the in-situ vehicle sensitivity function. The experimental data was used to correlate the analytical model. The testing results have shown that in the frequency range of the “garage shift” that the vehicle body can be represented as a rigid body. A Nastran model utilizing a rigid body representation of the body and powertrain is used to predict the vehicle response to the torque transient.

Driveline clunk is a phenomenon that can adversely affect customer perception of vehicle quality. Clunk is created by the impact of two driveline components as they oscillate in response to a torque disturbance in the driveline system. This disturbance is typically initiated by a driver controlled engine torque variation, most severely through a throttle or clutch manipulation. This torque variation excites a torsional response from the driveline, manifested by a variety of mechanisms such as resonances of various shafts, housings and axles, clutch oscillations, and gear impacts. Because automotive drivelines are complex systems composed of many rotating components, difficulty arises in identifying the impacts that cause clunk and evaluating the significant parameters that can positively affect these collisions. This paper will describe the application of analysis and test methods in the investigation of clunk in a rear wheel drive, manual transmission vehicle.

With the revolutionary advances in computing power and software technology, the future trend of integrating design and CFD analysis software package to realize an automated design optimization has been explored in this study. The integrated process of UG, ICEMCFD, and FLUENT was accomplished using iSIGHT for vehicle Aero/Thermal applications. Process integration, CFD solution strategy, optimization algorithm and the practicality for real world problem of this process have been studied, and will be discussed in this paper. As an example of this application, the results of an underhood thermal design will be presented. The advantage of systematical and rapid design exploration is demonstrated by using this integrated process. It also shows the great potential of computer based design automation in vehicle Aero/Thermal development.

Forward collision warning (FCW) systems are intended to provide drivers with crash alerts to help them avoid or mitigate rear-end crashes. To facilitate successful deployment of FCW systems, the Ford-GM Crash Avoidance Metrics Partnership (CAMP) developed preliminary minimum functional requirements for FCW systems implemented on light vehicles (passenger cars, light trucks, and vans). This paper summarizes one aspect of the CAMP results: minimum requirements and recommendations for when to present rear-end crash alerts to the driver. These requirements are valid over a set of kinematic conditions that are described, and assume successful tracking and identification of a legitimate crash threat. The results are based on extensive closed-course human factors testing that studied drivers' last-second braking preferences and capabilities. The paper reviews the human factors testing, modeling of results, and the computation of FCW crash alert timing requirements and recommendations.

In recent years, the slip lock-up mechanism has been adopted widely, because of its fuel efficiency and its ability to improve NVH. This necessitates that the automatic transmission fluid (ATF) used in automatic transmissions with slip lock-up clutches requires anti-shudder performance characteristics. The test methods used to evaluate the anti-shudder performance of an ATF can be classified roughly into two types. One is specified to measure whether a μ-V slope of the ATF is positive or negative, the other is the evaluation of the shudder occurrence in the practical vehicle. The former are μ-V property tests from MERCON® V, ATF+4®, and JASO M349-98, the latter is the vehicle test from DEXRON®-III. Additionally, in the evaluation of the μ-V property, there are two tests using the modified SAE No.2 friction machine and the modified low velocity friction apparatus (LVFA).

General Motors is developing a hybrid electric concept vehicle from its “Precept” high efficiency vehicle architecture, to satisfy requirements of the Partnership for a New Generation of Vehicles (PNGV) program. This Technology Demonstration Vehicle (TDV) features fundamental architecture that is unconventional compared to contemporary passenger car design, or even to other hybrid vehicles. This paper describes this unique architecture and how the vehicle's most significant features complement each other in harmonious design. It also notes how these features contribute to robustness of efficiency.

The CY2000 cornerstone goal of the Partnership for a New Generation of Vehicles (PNGV) is the demonstration in CY 2000 of a 5-passenger vehicle with fuel economy of up 80 mpg (3 l/100km). As a PNGV partner, GM will demonstrate a technology-demonstration concept vehicle, the Precept, having a lightweight aluminum-intensive body, hybrid-electric propulsion system and a portfolio of efficient vehicle technologies. This paper describes: 1) the strategy for the vehicle design including mass requirements, 2) the selection of dual axle application of regenerative braking and electric traction, and 3) the complementary perspective on energy management strategy. This paper outlines information developed through systems analysis that drove technology selections. The systems analyses relied on vehicle simulation models to estimate fuel economy associated with technology selections. Modeling analyses included consideration of both federal test requirements and more severe driving situations.

General Motors Powertrain Division has developed the next generation big block V8 engine for introduction in the 1996 model year. In addition to meeting tighter emission and on-board diagnostic legislation, this engine evolved to meet both customer requirements and competitive challenges. Starting with the proven dependability of the time tested big block V8, goals were set to substantially increase the power, torque, fuel economy and overall pleaseability of GM's large load capacity gasoline engine. The need for this new engine to meet packaging requirements in many vehicle platforms, both truck and OEM, as well as a requirement for minimal additional heat rejection over the engine being replaced, placed additional constraints on the design.